Technical Data
Product Information
DAA
Alpha-X / Race Master Insert Block
The insert block determines which pistol your Alpha-X or Race Master holster accepts: swap the block and you are done. This takes less than a minute and without losing any of the holster's settings. The fit therefore depends on the insert block, not on the base holster.
The DAA Alpha-X / Race Master Insert Block converts an existing competition holster to another firearm model in less than a minute without losing the holster position settings.
Firearm-specific locking block pre-assembled firearm-specific sliding lock for Alpha-X and Race Master holsters fast conversion without readjusting the holster
Important CZ note: CZ TS Czechmate and CZ TS Orange pistols exist with different trigger-guard/frame versions. The exact version must be checked at the trigger-guard area before ordering.
The insert-block principle comes from Double-Alpha Academy's Race Master holster, which DAA introduced in 2010, and carries on in the Alpha-X. Instead of building a separate holster for every pistol, an exchangeable block here carries the firearm shape; DAA has continued to refine the magnetic activation of the latest block generation.
- Pistol change in under a minute
The block is secured with two small M4 screws on the back of the holster; the swap is fast and loses none of the position settings.
- Firearm-specific locking block
The locking block is matched to the selected firearm model.
- Sliding lock with safety lever
The firearm-specific sliding lock comes assembled, as do the safety lever and the internal magnetic activation system.
- Hold at the trigger guard
The block grips the pistol only at the front end of the trigger guard, where a very precise fit is required. In some cases light modifications to the block may be needed.
- For right- and left-hand holsters
The insert blocks are designed for right- and left-hand holsters; the same block works in both.
Material and craftsmanship
Firearm-specific block with assembled sliding lock, safety lever and magnets; a plastic wedge and two steel pins are part of the assembly.
Available configurations
Compatible firearm models
CZ
- 75 SP-01
- 75 Tactical Sport Czechmate
- 75 Tactical Sport Orange
- P-09
- P-10 C
- P-10 F
- Shadow 2
- Shadow 2 Orange
- TS 2
- TS 3
Sig Sauer
- P210
- P226
- P226 X5
- P226 X6
- P228
- P320
- P320 X5
- P320 X5 Legion
Grand Power
- GP6
- K100
- X-Calibur MK07
- X-Calibur MK12
Smith & Wesson
- M&P
- All K-Frame models
- All L-Frame models
- All N-Frame models
Tanfoglio
- Standard
- Stock I
- Stock II
- Stock III
BUL Armory
- M5
- SAS
- SAS II
Walther
- PDP
- Q5 Match
- Q5 Match SF
Beretta
- 92F
- 92X Performance
Heckler & Koch
- USP
- VP9
Phoenix Arms
- Redback
- Trinity
Sphinx
- 3000
- SDP
STI
- DVC 2011
- Rangemaster
Arsenal Firearms
- Strike One
Canik
- TP9SF
Laugo Arms
- Alien
Springfield Armory
- XDM
Staccato
- HD
Further makers
- Caspian Arms
- Glock
- KMR
- Para Ordnance
- SPS
- SVI
Scope of delivery
- Locking block (firearm-specific)
- Sliding lock, assembled (firearm-specific)
- Safety lever, assembled
- Internal magnetic activation system, assembled
Notes
- Only for Alpha-X and Race Master holsters. Flex insert blocks are not compatible with these holsters.
- For a CZ TS Czechmate or CZ TS Orange, please contact DAA with a photo of the trigger-guard area before ordering: CZ ships pistols with two different trigger-guard styles.
- For the SIG 226/228 (not X5) the trigger guard should be about 11.5 mm (0.45 in) wide; for the X5 line about 13.5 mm (0.53 in).
- For round trigger guards (1911 steel frame, Para Ordnance, revolvers) DAA recommends the muzzle support.
- Test the fit only with an unloaded firearm; check retention and release before every use.
* Firearms, optics, magazines, ammunition and accessories shown are not included unless expressly stated. The selected article variant applies.
DAA
